ftp做外網登陸不了
vsftpd 做成外網訪問，
現在只出現登陸窗口，但是登不上，
還要在哪邊改啊
# Allow anonymous FTP? (Beware - allowed by default if you comment this out).
anonymous_enable=no
#
# Uncomment this to allow local users to log in.
local_enable=YES
#
# Uncomment this to enable any form of FTP write command.
write_enable=YES
#
# Default umask for local users is 077. You may wish to change this to 022,
# if your users expect that (022 is used by most other ftpd's)
local_umask=022
#
# Uncomment this to allow the anonymous FTP user to upload files. This only
# has an effect if the above global write enable is activated. Also, you will
# obviously need to create a directory writable by the FTP user.
anon_upload_enable=YES
#
# Uncomment this if you want the anonymous FTP user to be able to create
# new directories.
anon_mkdir_write_enable=YES
#
# Activate directory messages - messages given to remote users when they
# go into a certain directory.
dirmessage_enable=YES
#
# Activate logging of uploads/downloads.
xferlog_enable=YES
#
# Make sure PORT transfer connections originate from port 20 (ftp-data).
connect_from_port_20=YES
#
# If you want, you can arrange for uploaded anonymous files to be owned by
# a different user. Note! Using "root" for uploaded files is not
# recommended!
#chown_uploads=YES
#chown_username=whoever
#
# You may override where the log file goes if you like. The default is shown
# below.
#xferlog_file=/var/log/vsftpd.log
#
# If you want, you can have your log file in standard ftpd xferlog format
xferlog_std_format=YES
#
# You may change the default value for timing out an idle session.
idle_session_timeout=600
#
# You may change the default value for timing out a data connection.
#data_connection_timeout=120
#
# It is recommended that you define on your system a unique user which the
# ftp server can use as a totally isolated and unprivileged user.
#nopriv_user=ftpsecure
#
# Enable this and the server will recognise asynchronous ABOR requests. Not
# recommended for security (the code is non-trivial). Not enabling it,
# however, may confuse older FTP clients.
#async_abor_enable=YES
#
# By default the server will pretend to allow ASCII mode but in fact ignore
# the request. Turn on the below options to have the server actually do ASCII
# mangling on files when in ASCII mode.
# Beware that on some FTP servers, ASCII support allows a denial of service
# attack (DoS) via the command "SIZE /big/file" in ASCII mode. vsftpd
# predicted this attack and has always been safe, reporting the size of the
# raw file.
# ASCII mangling is a horrible feature of the protocol.
ascii_upload_enable=YES
ascii_download_enable=YES
#
# You may fully customise the login banner string:
ftpd_banner=Welcome to blah FTP service.
#
# You may specify a file of disallowed anonymous e-mail addresses. Apparently
# useful for combatting certain DoS attacks.
#deny_email_enable=YES
# (default follows)
#banned_email_file=/etc/vsftpd/banned_emails
#
# You may specify an explicit list of local users to chroot() to their home
# directory. If chroot_local_user is YES, then this list becomes a list of
# users to NOT chroot().
#chroot_list_enable=YES
# (default follows)
#chroot_list_file=/etc/vsftpd/chroot_list
#
# You may activate the "-R" option to the builtin ls. This is disabled by
# default to avoid remote users being able to cause excessive I/O on large
# sites. However, some broken FTP clients such as "ncftp" and "mirror" assume
# the presence of the "-R" option, so there is a strong case for enabling it.
#ls_recurse_enable=YES
#
# When "listen" directive is enabled, vsftpd runs in standalone mode and
# listens on IPv4 sockets. This directive cannot be used in conjunction
# with the listen_ipv6 directive.
listen=YES
#
# This directive enables listening on IPv6 sockets. To listen on IPv4 and IPv6
# sockets, you must run two copies of vsftpd whith two configuration files.
# Make sure, that one of the listen options is commented !!
#listen_ipv6=YES
pam_service_name=vsftpd
userlist_enable=YES
tcp_wrappers=YES
《解決方案》
您是弄成匿名用戶、系統用戶還是虛擬用戶登陸？登陸的時候出現什麼錯誤提示呢？您的系統有防火牆嗎？有對外開放ftp的埠嗎？
貼出錯誤信息。。。。（登錄失敗后，執行tail -f /var/log/message可得錯誤信息）
《解決方案》
原帖由 diyself 於 2009-4-8 11:23 發表 http://bbs3.chinaunix.net/images/common/back.gif
您是弄成匿名用戶、系統用戶還是虛擬用戶登陸？登陸的時候出現什麼錯誤提示呢？您的系統有防火牆嗎？有對外開放ftp的埠嗎？
貼出錯誤信息。。。。（登錄失敗后，執行tail -f /var/log/message可得錯誤信息）
1. 不是匿名用戶，而已/home/xx這個xx的用戶，應該是虛擬用戶吧，不是很明白
2.在內網用外網的IP訪問時，就是用xx用戶的，但登陸不了，一直出現登陸窗口，而內網卻正常可以登
3，系統關掉防火牆了，好像沒有對外開放埠，只在路由開了個埠，不知道是不是這個
4.tail -f /var/log/message
# tail -f /var/log/message
tail: 無法打開 「/var/log/message」 讀取數據: 沒有那個文件或目錄
tail: no files remaining
《解決方案》
回復 #3 xfen 的帖子
您用的還是系統帳戶吧。
內外正常訪問，外網能訪問到ftp伺服器，登陸不上，是防火牆的問題吧？
《解決方案》
原帖由 diyself 於 2009-4-8 16:38 發表 http://bbs3.chinaunix.net/images/common/back.gif
您用的還是系統帳戶吧。
內外正常訪問，外網能訪問到ftp伺服器，登陸不上，是防火的問題吧？
那麼我再建個用戶的話，再試下
但防火牆確定是關了，
《解決方案》
原帖由 xfen 於 2009-4-8 19:05 發表 http://bbs2.chinaunix.net/images/common/back.gif
那麼我再建個用戶的話，再試下
但防火牆確定是關了，
期待lz的好消息。
《解決方案》
回復 #6 diyself 的帖子
這樣的,我建了useradd hh用戶,然後內網訪問正常,
但用外網訪問的話呢,不加埠就登陸不上,一直是登陸的窗口
加上埠的話就windows無法訪問些文件,
詳細信息:無法與伺服器建立連接,
注:red hat 5.3
selinux=disable
kernel /vmlinuz-2.6.18-8.el5 ro root=/dev/VolGroup00/LogVol00 rhgb quiet selinux=0
不知道這些有沒有影響,還是貼出來,全面了解
